Lime Production Line
Dust Collection and Gas Treatment in Lime Production Plants
2026-09-28 15:24:32
We are Liming Heavy Industry, a manufacturer of various types of industrial crushers, such as Raymond Mill, Trapezoidal Mill, Vertical Mill, Ultrafine Mill, Ball Mill, etc.
Our mills can process the following minerals:
limestone, quicklime, kaolin, talc, barite, bentonite, calcium carbonate, dolomite, coal, gypsum, clay, carbon black, slag, cement raw materials, cement clinker, etc.
If you need a mill to process stone or minerals into powder, please feel free to contact me (WhatsApp: +8615333807511). Thank you.
A lime plant has two distinct air-control jobs: capture dust where stone or lime is handled, and treat the gases leaving the kiln. A filter on the kiln stack does not control dust escaping from a transfer point, while a crusher-area collector does not address combustion-related gases. The design should map every exhaust and dust-release point from raw-stone preparation through product loading.
Follow the material through the plant
| Plant area | Typical release point | Design consideration |
|---|---|---|
| Limestone preparation | Crusher inlets and discharges, screens, conveyor transfers | Enclose dusty points where practical and extract air to appropriately sized collectors. |
| Kiln and preheater | Main exhaust-gas stream | Account for gas flow, temperature, dust loading and pollutants requiring treatment. |
| Quicklime cooler | Separate cooler exhaust, if not returned to the kiln | Determine whether the air is reused or needs its own particulate control. |
| Grinding and product handling | Mill circuit, screens, enclosed transfers, silo filling and loading | Contain fine lime and provide a controlled outlet for dust-bearing displaced air. |
| Hydration, if installed | Hydrator vapor-and-dust exhaust | Specify collection for this stream's moisture and temperature rather than copying a dry transfer-point filter. |
Collect dust close to where it forms
Covered conveyors and enclosed transfers reduce the amount of dust that can escape. Where extraction is needed, the enclosure, duct, fan and collector must work as a system: insufficient airflow allows dust to leak out, while poor duct design lets material accumulate. Fabric filters are commonly used for dusty handling operations. Crushers, screens, mills and silos may need separate collection arrangements because their airflows and operating cycles differ.
At a silo, filling displaces air. Provide filtration and a suitable pressure-management arrangement so the silo can fill without forcing dust through unintended openings. Loading equipment should likewise capture dust at the point where lime enters a truck or container. Quicklime-handling systems should be designed to prevent unwanted moisture entry; water sprays suitable for some limestone stockpiles are not a general solution for quicklime dust.
Treat the kiln stream on its own terms
The kiln is often a major ducted source of particulate matter. Coarse-particle separation may be followed by a fabric filter or electrostatic precipitator, depending on the gas conditions and plant design. The inlet temperature, dust load and expected operating changes—including startup and shutdown—must be considered when selecting the equipment and its protective controls.
Dust removal is not the same as gas treatment. Lime kilns may emit nitrogen oxides, sulfur dioxide and carbon monoxide, as well as carbon dioxide from both fuel combustion and limestone calcination. The amounts depend on factors including fuel, stone composition, kiln design and operation. Where a site must control a particular gas, evaluate process adjustments and any additional treatment against measured or defensible project-specific emissions data. A particulate filter alone should not be presented as a solution to every gaseous pollutant.
Keep collected materials identifiable
Dust captured from kiln exhaust, limestone crushing and finished-lime handling may differ in composition. Do not assume that all collected dust can be returned to the same point in the process or sold as finished product. Establish collection, sampling and discharge routes that let the plant assess each stream before reuse or disposal.
Monitoring should match the control equipment and the site's permit. Useful operating checks can include collector pressure drop, fan performance, visible leaks and the condition of filter elements, alongside any required stack measurements. A rising pressure drop or repeated dust escape calls for investigation of the collection system, not merely a higher fan setting.
Specify the complete control scope
When requesting a plant proposal, provide the kiln type and fuel, expected exhaust conditions, limestone and product-handling layout, cooler vent arrangement, any grinding or hydration stages, and the applicable local emission limits. Ask the designer to identify each collection point, exhaust destination, treatment device, monitoring provision and collected-dust route. This makes it possible to assess air control as part of a working lime line rather than as a single filter added after the equipment is chosen.
